[[TOC(depth=-1)]] = LSI Fusion MPT SAS = [[Image(wiki:LSI:logo_lsi.gif)]] [[BR]][[BR]] = 1. Card information = The FusionMPT SAS2 is a low-end card from LSI. It replaces the Fusion MPT cards. [[BR]]It only supports RAID0 and RAID1 an can usually be found in many 1U rackmount servers which have only two disks drives. However, I must admit I'm not sure yet there's no RAID5 adapter with thoses chips. [[BR]]Even it's not full of features theses card appear to work fine and are supported by an '''opensource Linux driver'''. [[BR]]A proprietary monitoring tool is available but it's nearly offer '''no management features'''. [[BR]] = 2. Linux kernel drivers = || Driver || Supported cards || || mpt2sas || LSI FusionMPT SAS 2.0 cards || There are many more mpt* drivers in Linux kernel. [[BR]]Somes seems to be required dependencies. Others looks like being real driver but we haven't used them yet. ''mpt2sas'' has been added to Linux kernel '''from 2.6.30 release'''. Thus, it should be available in all '''recent (2010+) Linux distributions'''. Some ''lspci -nn'' output examples: * 01:00.0 Serial Attached SCSI controller [0107]: LSI Logic / Symbios Logic SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] [1000:0072] (rev 02) ''Dell PERC H200'' [[BR]] = 3. Management and reporting tools = There are '''no management tool'''. LSI doesn't provide any proprietary utility for FusionMPT's cards. [[BR]]However an '''opensource reporting tool''' named ''mpt-status'' has been developped. == 3.1. mpt-status == === 3.1.1. Quickstart and output example === Probe controllers IDs:[[BR]] {{{ server:~# mpt-status -p Checking for SCSI ID:0 Found SCSI id=0, use ''mpt-status -i 0`` to get more information. }}} Get status of controller "0":[[BR]] {{{ server:~# mpt-status -i 0 ioc0 vol_id 0 type IM, 2 phy, 73 GB, state OPTIMAL, flags ENABLED ioc0 phy 1 scsi_id 32 ATA ST3808110AS J , 74 GB, state ONLINE, flags NONE ioc0 phy 0 scsi_id 1 ATA ST3808110AS J , 74 GB, state ONLINE, flags NONE }}} In most case, your controller ID will be 0. Running ''mpt-status'' '''without any parameters''' will give you the same output example as above. You '''MUST''' have '''mptctl''' kernel module '''loaded''' to monitor your RAID HBAs.[[BR]] Load it by hand for the first time and add it to '''/etc/modules''' for next reboots:[[BR]] {{{ modprobe mptctl echo mptctl >> /etc/modules }}} === 3.1.2. My opinion about mpt-status === Despite it seems that '''no real upstream development''' exists for this tool, it works '''fine''' and is '''reliable'''. [[BR]]We experienced several disks failure on MPT SAS controllers and mpt-status always reported the failure and status changes. [[BR]]However don't expected verbose output. Homepage: http://www.drugphish.ch/~ratz/mpt-status/ === 3.1.3. Reporting with mpt-status === ''mpt-status'' has been greatly integrated to Debian by '''Petter Reinholdtsen and Steffen Joeris'''. [[BR]]Many thanks to them for good work ! The packages comes with an initscript that '''periodic''' run mpt-status to '''check status'''. [[BR]]It keeps a file with latest status and thus is able to detect RAID '''status changes and/or brokeness'''. [[BR]]It will log a ligne to '''syslog''' when something failed and will send you a '''mail'''. [[BR]]Until arrays are healthy again a '''reminder''' will be sent each 2 hours. In fact, I must admit all my ''"something-status"'' packages for others kind of cards are based on this work. == 3.2. lsiutil == This tool comes from LSI. Its sources (for Linux systems) are available but the license is not specified. [[BR]]I haven't use it much, so here is a quick example of what it can do: {{{ server:~# lsiutil LSI Logic MPT Configuration Utility, Version 1.56, March 19, 2008 1 MPT Port found Port Name Chip Vendor/Type/Rev MPT Rev Firmware Rev IOC 1. /proc/mpt/ioc0 LSI Logic SAS1068E B3 105 00143000 0 Select a device: [1-1 or 0 to quit] 1 1. Identify firmware, BIOS, and/or FCode 2. Download firmware (update the FLASH) 4. Download/erase BIOS and/or FCode (update the FLASH) 8. Scan for devices 10. Change IOC settings (interrupt coalescing) 13. Change SAS IO Unit settings 16. Display attached devices 20. Diagnostics 21. RAID actions 22. Reset bus 23. Reset target 42. Display operating system names for devices 45. Concatenate SAS firmware and NVDATA files 60. Show non-default settings 61. Restore default settings 69. Show board manufacturing information 97. Reset SAS link, HARD RESET 98. Reset SAS link 99. Reset port e Enable expert mode in menus p Enable paged mode w Enable logging Main menu, select an option: [1-99 or e/p/w or 0 to quit] 1 Current active firmware version is 00143000 (0.20.48) Firmware image's version is MPTFW-00.20.48.00-IE LSI Logic x86 BIOS image's version is MPTBIOS-6.14.10.00 (2007.09.29) Main menu, select an option: [1-99 or e/p/w or 0 to quit] 21 1. Show volumes 2. Show physical disks 3. Get volume state 4. Wait for volume resync to complete 23. Replace physical disk 26. Disable drive firmware update mode 27. Enable drive firmware update mode 30. Create volume 31. Delete volume 32. Change volume settings 33. Change volume name 50. Create hot spare 99. Reset port e Enable expert mode in menus p Enable paged mode w Enable logging RAID actions menu, select an option: [1-99 or e/p/w or 0 to quit] 2 1 volume is active, 2 physical disks are active PhysDisk 0 is Bus 0 Target 1 PhysDisk State: online PhysDisk Size 238418 MB, Inquiry Data: ATA ST3250620NS 3BKS PhysDisk 1 is Bus 0 Target 8 PhysDisk State: online PhysDisk Size 238418 MB, Inquiry Data: ATA ST3250620NS 3BKS RAID actions menu, select an option: [1-99 or e/p/w or 0 to quit] 1 1 volume is active, 2 physical disks are active Volume 0 is Bus 0 Target 0, Type IM (Integrated Mirroring) Volume Name: Volume WWID: 01e2adb8d959aedc Volume State: optimal, enabled Volume Settings: write caching enabled, auto configure, priority resync Volume draws from Hot Spare Pools: 0 Volume Size 237464 MB, 2 Members Primary is PhysDisk 1 (Bus 0 Target 8) Secondary is PhysDisk 0 (Bus 0 Target 1) RAID actions menu, select an option: [1-99 or e/p/w or 0 to quit] 3 Volume 0 State: optimal, enabled RAID actions menu, select an option: [1-99 or e/p/w or 0 to quit] }}} [[BR]] = 4. BIOS upgrade from a Linux system = Sorry, we don't have any informations about this. [[BR]][[BR]]